Cartridge replacement tutorial: How to avoid leaks and maintain the best taste
Cartridge replacement tutorial: How to avoid leaks and maintain the best taste
Blog Article
For users of Endura V vapes, cartridge replacement is a basic operation. Correct replacement of cartridges can not only avoid leakage problems but also ensure that the best taste is always maintained. The following is a detailed tutorial for replacing cigarette cartridges.
1. Preparatory Work
Before replacing the cartridges, make sure your hands are clean and dry to avoid stains or moisture on your hands contaminating the cartridges. Meanwhile, prepare the new cartridges. The Endura V is compatible with 3 VCAP cartridges, allowing you to select your favorite flavors in advance.
2.Remove the old cigarette cartridges
(1) Power-off operation (if any)
If the equipment has a switch, turn it off first to ensure that the equipment is in a power-off state. This step is mainly to prevent the equipment from accidentally starting up during the disassembly of the cartridgers, which could cause unnecessary risks.
(2) Disassemble the old cartridges
Gently hold the device and find the connection part between the cartridge and the device. Generally speaking, cigarette cartridges are connected to the device by plugging and unplugging. Pinch the bottom of the cartridge with your fingers and gently pull it out vertically upwards. The movement should be gentle to avoid excessive force causing the liquid in the cartridge to spill out. If the cartridge is tightly connected to the device, you can slightly rotate the cartridge left and right before pulling it out.
After removing the old cartridges, carefully observe the cartridges slot and the suction nozzle part of the equipment. If there is any residual liquid, gently wipe it clean with a clean paper towel. At the same time, check if there are any foreign objects or blockages in the cartridges slot. If so, carefully clean them with a small brush or toothpick.
3. Install new cartridges
(1) Check the new cartridges
Before installing new cartridges, first check whether there is any damage or leakage on the appearance of the cartridges. Ensure that the sealing film of the cartridge is intact and the electrode part is clean without any foreign objects. If any quality problems with the cartridges are found, they should be replaced in time.
(2) Installation and Operation
Align the electrode part of the new cartridge with the electrode contact point in the cartridge slot of the device and insert it vertically downward gently. When a "click" is heard, it indicates that the cigarette cartridge has been installed in place. At this point, the cigarette cartridge is in good contact with the electrode of the equipment and can work normally.
During the installation process, it is important to keep the cartridge vertical and avoid inserting it at an Angle. Otherwise, it may lead to a loose connection between the cartridge and the equipment, increasing the risk of leakage. Meanwhile, do not press the cartridges too hard to prevent damage to the cartridges or the slots of the equipment.
4. Tips for Avoiding Leakage and Maintaining Taste
(1) Avoid leakage
After installing the e-cartridges, do not use them immediately. First, let the device stand for 1 to 2 minutes to allow the e-liquid in the e-cartridges to fully soak the atomization core. This can reduce the leakage caused by insufficient e-liquid soaking during the first use.
During daily use and carrying, try to keep the device upright and avoid tilting or inverting it to prevent the liquid from flowing towards the suction nozzle due to gravity and causing leakage.
If the equipment is not used for a long time, it is recommended to remove the cartrids and store them separately. This can reduce the contact between the cartrids and the air inside the equipment, lowering the risk of leakage and oxidation.
(2) Maintain the best taste
Each time you replace a new cartridge, do a few light puffs (without lighting) first to allow air to circulate inside the cartridge, which helps the liquid to be better distributed. This way, you can enjoy the best taste from the first sip.
Regularly clean the suction nozzles and atomization cores of the equipment to keep them clean. The suction nozzle can be rinsed with warm water and then dried naturally. If there is carbon deposit or blockage in the atomization core, it can be cleaned or replaced according to the equipment manual to ensure that the atomization effect is always good.
Try to use up the e-liquid within its shelf life. As time goes by, the e-liquid in the e-liquid may undergo oxidation and other changes, which will affect the taste.
Through the above cartridge replacement tutorial and related tips, users can correctly replace the cartridgers of Endura V, effectively avoid leakage problems, and continuously enjoy the best vaping taste. Report this page